Hook, Needle & Hoop Subscribe

Home › Guides

Visible Mending for Beginners: Darning and Sashiko-Style Patches

How to fix a hole in a sock or sweater with a woven darn, and a worn spot in jeans with a sashiko-style patch. No sewing experience needed.

Close-up of a square woven darn in mustard-yellow thread on gray knitted fabric.Illustrative image
A woven darn in a contrasting color on a knit.

Visible mending means fixing a hole or worn spot so the repair shows, on purpose. You use a contrasting thread or a patch and let it be part of the garment. This guide starts with the easiest fix, sewing on a button, then teaches two visible fixes: a woven darn for knitted fabric (socks, sweaters), and a sashiko-style patch for woven fabric (jeans, shirts).

Your first mend will look uneven. That's expected, and it's part of the look.

A quick note on terms: This guide uses US terms, with the UK word in brackets where it differs: sweater [UK: jumper], embroidery floss [UK: stranded cotton]. Sashiko is a Japanese stitching tradition that uses rows of small running stitches to reinforce and mend cloth. What we teach here is sashiko-style: the same running stitch, used the way many beginner mending tutorials use it. It isn't traditional sashiko, which has its own patterns and teachers.


Part 1: Tools and supplies

You may already own most of what you need. Our free Starter Kit includes a mending checklist.

For the practice darns and patches in this guide, choose a thread color that contrasts with the garment. It's easier to see what your stitches are doing. For a button (Part 3), match the thread to the thread on the other buttons, or to the fabric. If you only have a close color, pick the slightly darker one.

A common next question is whether a first decorative mend should match or contrast. Matching thread hides the repair. Contrasting thread is the visible-mending look, and it helps while you are learning, because you can see each stitch. Straight, even rows of running stitch are enough for a first design; grids and motifs can wait.


Part 2: Which fix suits which damage

Before you pick up a needle, press the fabric next to the hole between your fingers. If it tears under light pressure, the area is too thin to hold stitches, and a mend won't last.

A darn rebuilds the missing fabric with thread alone (warp one way, weft the other). A patch adds a piece of cloth behind or on top of the damage, then stitches it down. There aren't hard rules, but for a first mend it is common to darn knits (socks, sweaters) and to patch woven cloth (jeans, shirts), especially when the area around the hole feels thin.

A clean tear, where the edges still meet and the cloth around them is sound, is different from a hole with fabric missing. On woven cloth such as jeans, both get the same fix in this guide: a sashiko-style patch behind the damage (Part 5), with rows of running stitch that cross the tear and run past both ends onto sound cloth. For a hole in a knit, use a woven darn (Part 4). If the cloth near the damage feels thin but passes the pinch test, cut the patch big enough to reach past the thin area onto solid fabric.

What you're fixing Fix Notes
Loose or missing flat button Sew on a button (Part 3) Matching thread; pin spacer for a stem
Hole in a sock or sweater Woven darn (Part 4) Needs a mushroom, egg or similar
Thin spot in knitting, not yet a hole Swiss darning (duplicate stitch), covered in the mending directory Follows the stitches; a step up from the woven darn
Hole or worn knee in jeans or other woven cloth Sashiko-style patch (Part 5) The patch goes behind the hole
Clean tear in woven cloth, edges still meet Sashiko-style patch (Part 5) Rows cross the tear and run past both ends onto sound cloth
Small hole or stain on a shirt Embroidery over the spot, see the directory Decorative stitching on a woven base

High-friction spots on jeans, such as the seat and inner thigh, put more strain on hand stitching, so they are harder first mends. For a first mend, choose a low-stress spot, such as a sweater elbow, a sock heel, or a tear above the knee bend. A worn denim knee is a common first hard spot. Pin and baste with the leg bent (Part 5), use a patch that reaches onto strong cloth past the thin area, and expect more strain than on a flat tear above the bend. Seat and inner-thigh wear are harder still; save those for later. Optional idea: if you already sew by machine, one tutorial suggests stitching the patch on underneath first and adding the visible hand stitches on top.


Part 3: Sew on a flat button

A loose button is the usual first fix. It uses matching thread. Save contrasting thread for the visible darns and patches later in this guide.

You need a sharp hand-sewing needle, about 24 in (60 cm) of all-purpose thread, the button, a pin (or toothpick) and scissors. Match the thread to the thread on the other buttons, or to the fabric. If you only have a close color, pick the slightly darker one.

  1. Double the thread and knot the ends together.
  2. Mark the spot (use the old stitch holes, or button the garment and mark through the buttonhole). Bring the needle up from the back so the knot sits on the wrong side.
  3. Lay the pin across the top of the button as a spacer so the stitches stay a little loose. Come up through one hole and down through the opposite hole. On a four-hole button, match the other buttons: either two parallel pairs or an X. Make 3 or 4 passes through each pair of holes.
  4. Take out the pin. Bring the needle up between the button and the fabric (not through a hole), wrap the thread around the stitch stack 3 to 4 times to make a short stem (a thread shank), then push the needle to the back.
  5. Finish with a few small stitches and a knot on the back, then trim.

Shank buttons (a loop on the back, no holes on the face) need no pin spacer. Pass the needle through the shank and the fabric until the button feels secure, then knot on the back.


Part 4: A woven darn on a knit

A woven darn replaces the missing fabric with a small woven patch. First you lay threads across the hole in one direction (the warp, running up and down). Then you weave threads through them in the other direction (the weft, side to side).

The drawings are simplified. The warp drawing shows seven threads and the weft drawing shows five; a real darn uses as many as it takes to cover your hole.

1. Stabilize the hole

Slide the mushroom or egg inside the sock or sweater so the hole sits in the middle of the smooth, curved top. Fix the fabric with a rubber band around the stem. The fabric should be held flat, not too tight and not too loose.

On a sweater, an embroidery hoop can also keep the knit from stretching.

Sock over a darning mushroom. Diagram, side view. A sock is pulled over the rounded top of a darning mushroom, and the mushroom handle comes out below. The hole sits in the middle of the dome, and the wooden mushroom shows through it. A rubber band around the sock at the neck holds the fabric flat on the dome, not stretched tight and not floppy.
A sock over a darning mushroom, with the hole centered on the dome.

2. Thread up and set your margin

Cut a length of yarn or thread about as long as your arm, and thread the needle. You don't need a starting knot on a knit. Leave a tail of about 4 in (10 cm) hanging on the back. The first catch into a solid knit stitch is what secures the start. Keep that tail free so you can weave it in at the end.

Your darn should be bigger than the hole. Start about ½ in (about 1.3 cm) beyond the damage, on solid fabric, and go wider if the edge is frayed or thin. That margin gives the stitches something strong to hold.

3. Lay the warp threads

Bring the needle up through solid fabric on one side of the hole, then catch one stitch of the knit and pull the thread through firmly, but not tightly. Take the thread across the hole and catch a stitch on the far side, just beyond the damage. That's one warp thread.

Come back the other way next to it, and repeat. Place the threads side by side, close together, until they cover the hole and extend past its edges. An odd number of threads makes the weaving easier.

Warp threads laid across a hole. Diagram, front of a knit. A hole has a dashed outline. Seven warp threads run straight up and down across it, side by side. One continuous thread turns at the top and the bottom, and each turn catches a stitch of solid knit about half an inch (about 1.3 cm) beyond the hole. The two thread tails also end in a knit stitch, marked with a V. The threads cover the hole and extend a little past its sides.
Warp threads run up and down, each turn catching a stitch ½ in beyond the hole.

4. Weave the weft

Now weave the weft at right angles to the warp. If your warp threads run up and down in front of you, the weft rows run side to side. Catch a stitch of the knit at the corner of the warp to anchor the thread. Then pass the needle over one warp thread and under the next, all the way across. At the edge, catch a stitch of the knit to anchor the thread, then weave back the other way, going over the threads you went under before. Keep alternating. You don't need to turn the piece. If you find it easier to always work from right to left, turn it half a turn (180°) after each row.

Push the rows up gently so they sit close together. Pass the needle between the warp threads, not through them, because going through a thread splits it.

Weft woven over and under the warp. Diagram, front of a knit, with no turning of the piece. Five warp threads run up and down. Yellow weft rows run side to side, crossing the warp at right angles, passing over one warp thread and under the next. Row 1 goes over warps 1, 3 and 5. Row 2 goes over warps 2 and 4, so every crossing flips from the row before. Four rows are finished and row 5 is half done: a blunt tapestry needle is passing under warp 4, with its tip just to the right of it. A bracket shows the warp ends about half an inch (about 1.3 cm) beyond the hole, and V marks show the turns caught in knit stitches.
Over one, under one, and each row reverses the row before.

5. Finish

Don't tie a finishing knot. A knot inside a sock can be uncomfortable. Thread the needle with each tail and weave it under the stitches around the edge of the darn on the back for about 1 to 2 in (2.5 to 5 cm), going the longer way with smooth cotton thread, then trim. The back should look flat, with no lumps. Gentle steam from an iron can help set the threads.


Part 5: A sashiko-style patch on jeans

This patch goes on the inside, behind the hole, and rows of running stitch hold it on from the outside. Sources suggest a first patch should be plain: straight, even rows.

1. Prepare the patch

Trim loose threads around the hole. Cut a patch of woven cotton or denim about 1 in (2.5 cm) larger than the hole on every side. (Tutorials range from ½ in to at least 1 in. Go bigger if the fabric around the hole is thin.) For a neater look, fold the raw edges under about ½ in (about 1.3 cm) and press them. Folding uses up some of the overlap, so if you fold, cut the patch 1½ in (4 cm) larger than the hole on every side.

2. Place and baste

Turn the jeans inside out. Put the patch behind the hole and pin it, with no wrinkles, then baste it with long, loose temporary stitches through the patch and that one layer of the jeans only. On a knee, hold the leg in its bent, worn position as you pin. If you pin it flat, the patch can pucker when the leg bends.

Patch pinned and basted behind a hole. Diagram, the inside of the jeans (turned inside out). A woven cotton patch sits behind the hole, which is shown as a dashed outline under the patch. The patch reaches about 1 inch (2.5 cm) past the hole on every side. Four pins hold it at the corners, and a dashed line of long, loose basting stitches runs around its edge. A dotted line near the left edge is labeled as the seam.
A patch pinned behind the hole, with long, loose basting around its edge.

3. Stitch the rows

Cut about 18–24 in (45–60 cm) of thread. A longer piece tangles. Knot one end.

Take out the pins; the basting now holds the patch. Turn the jeans right side out and slide a piece of cardboard inside the leg, under the patch, so the needle can't catch the back of the leg. Start from the inside so the knot stays hidden, then work the rows on the outside. Stitch parallel rows of running stitch, about ¼ in (6 mm) apart, through both the jeans and the patch. Aim for stitches about the size of a grain of rice, roughly 4 to 8 to the inch, with the stitches on the back a little shorter than those on the front. A long needle lets you load several stitches before you pull the thread through.

Let each row start and end slightly beyond the patch, on the jeans, so the stitching holds the patch's edges down.

Parallel rows of running stitch. Diagram, the outside of the jeans. Eight straight, parallel rows of running stitch run left to right across the patch, which is behind the dotted outline. The rows are about one quarter inch (6 mm) apart and run a little past the patch edges onto the jeans. Each stitch is about the size of a grain of rice, roughly 4 to 8 stitches per inch.
Straight rows of running stitch, about ¼ in (6 mm) apart, past the patch edge.

If you want a grid, add a second set of rows at right angles to the first. If you want straight lines, draw them first with an erasable pen, and test the pen on a scrap.

4. Turn and finish

At the end of a row, don't pull the thread tight before you turn. Leave a small loop on the inside, which gives the fabric room to move. At the end, run the needle under a few stitches on the back, knot, and trim. Remove the basting and the cardboard.


Part 6: Common problems

Why is my mend puckering?

Usually the thread is pulled too tight, or the fabric was stretched when you pinned or mounted it. Ease the tension, and re-stitch the puckered part more loosely. In sashiko-style rows, leaving a small loop at each turn also helps.

Why does my darn feel stiff or lumpy?

A darn pulled too tight goes stiff. Pull the thread through firmly but not tightly. Check the fabric on the mushroom too: it should be held neither stretched nor floppy. Don't knot the ends, because knots inside a sock can be uncomfortable. Weave the tails in around the edge of the darn.

Why won't my patch lie flat?

A common cause is pinning it while the garment is flat, when it's worn bent. Pin it in place with the garment shaped as it will be worn, smooth out wrinkles first, and baste before you stitch. Stretchy fabric also warps under stitches, so choose non-stretch cloth for a first patch.

Why is the fabric around the hole still wearing thin?

If the fabric around the hole is thin, a new hole can open up next to the mend. Make the darn or patch bigger than the hole, so it covers the thin edge. For a worn spot that hasn't yet become a hole, Swiss darning is a good way to reinforce it. If the fabric tears when you pinch it, it's too far gone for a hand mend.

How do I start and finish the thread on a knit?

No starting knot. Leave a 4 in (10 cm) tail, catch the first stitch in solid knit, and weave both tails under the darn on the back at the end. Skip knots inside socks and other wear-next-to-skin knits.


Where to go next

The photo at the top of this guide is an AI-generated illustration, labeled “Illustrative image”. A real first darn will look more uneven than this one. The step diagrams are drawn for this site. Trust the written steps for exact details.

Back to top ↑